How much should I pay to have a water pump replaced?

water is leaking from my car, i took it in right now and they say its the water pump that's broken, so they said it'll be 60 dollars for the cost of the water pump, AND $240 more for the labor of having to put it in, ive never had this done before so does anyone know if that's a decent price? Should i be paying more, or less?How much should I pay to have a water pump replaced?That actually isnt too bad. It typically can depend on the brand and how easy the labor is.. I have a 1987 VW Golf and they charged me around 450 to install a new one. But if in doubt, shop around a little.How much should I pay to have a water pump replaced?Sounds about right....



On some vehicles replacing a water pump can require alot of work.How much should I pay to have a water pump replaced?You can buy the water pump and install it yourself. You can probably get one for less than $60 if you shop around.



Check the car over yourself or get a 2nd opinion, it could be a leaking hose which will cost a lot less to replace than the water pump.



On the other hand it could be a leaky radiator. This will cost you more, but left unattended it will cost you even more.How much should I pay to have a water pump replaced?get a mechanic friend to help, (wiki answer below)



Remove fan shroud, fan, and belts. Get a 15/16 socket and remove the nut that holds the crankshaft pulley on and remove the pulley. You really need to get a Haynes or Chilton manual because this part has to be done right or you are letting yourself in for all kinds of trouble. Remove upper and lower timing belt covers and make a diagram of where the bolts go, as they are not all the same. You MUST align the marks on both the camshaft pulleys with the little dots on the timing belt covers.(at 3 o'clock)This should align the key on the camshaft pulley with the hash mark on the inside cover(at 3 o'clock also). Remove the two bolts holding the hydraulic belt tensioner in and remove it. You will need to compress it in a vise and put a nail thru the holes in it to be able to reinstall it. Then slip the timing belt off. Be SURE you DO NOT move the pulleys out of alignment. The water pump is in the top center of the block, has 11 or 12 bolts in it. Remove it, clean the gasket area and replace it. And then reassemble. It is not easy, and I had a Haynes manual to help me.

i hold a computer problem

speakers won't work

How do i change water pump on 1996 Ford Probe?

Hi, i need a little help, i need to change the water pump on my 1996 Ford Probe 2.5 24v V6. Does anyone know the easiest way to do it? Im pretty good with engines so would rather change it myself than spend a fortune on labour at a garage!



Thanks in advance!How do i change water pump on 1996 Ford Probe?I would defo change it myself as the price you would pay a garage to do it would probably be enough to buy another Probe without a broken waterpump.



The car will not be worth what it once was, but that doesn't stop it from being a decent car. Buy a Haynes manual and get stuck in, that's the best way.



The more maintenance you do yourself the more money you save and the more you get to know your cars insides. And the money you save you can use for petrol (thirsty buggers)!How do i change water pump on 1996 Ford Probe?if its not different than the 1998 ford contour, this is what I would do.



Remove the serpentine belt

Remove the water pump pulley, not easy. 3 bolts

remove the water pump with the T5(I think) head, 3 bolts



It was easy for my 1998 ford contour. I think it is similar to yours.



Good Luck.How do i change water pump on 1996 Ford Probe?Your best bet is to purchase a repair manual for your car. Follow the instructions in there without taking any short cuts and you should be fine.How do i change water pump on 1996 Ford Probe?take off the belt or belts .you may have to take off the motor mount to get the water pump off butt if you have the new one wit you you can just follow where the bolts are to remove then and then put them back in that order to put the water pump back in,. the labor would be a lot but if you have half a day you can do it your self by taking your time to make sure you put the parts back in the same place

How do you make the wooden base for a manual water pump?

i have an underground water tank, my jet pump went out again, got a new one, waiting for the guy to come install it. i got an old fashioned iron hand pump, for when the electric, or the pump goes out again, i can pump out water. got pipes, fittings, foot valve. i just dont know what kind of base to make ,to bolt pump to, over the pipe that will come out of the ground. any ideas?How do you make the wooden base for a manual water pump?you can make a wooden floor cover using a treated good lumber of 1%26quot; X 6%26quot; for the floor and 2%26quot; X 6%26quot; lumber for the floor joist.



assemble the 2X6%26quot; lumber for the floor joist. depending on the top area of your water tank. arrange the floor joist at 0.60 meter spacing and 1.2 meter braces.



after that, use 1X6 lumber as flooring with at least 2 cm spacing between lumber.



as on the base of your pump, you can reinforce it by adding 2X6 braces.



use a lug bolt depending on the size of the slot at the base of your pump then bolt it on top of the 1X6 flooring.



its better if we can draw it here to make it easier to understand and explain



i dont know if this can help much because we havent seen the actual situation of your tank and your pump.

How difficult is it to replace a water pump on a 1990 mercury Grand Marquis?

My water pump is starting to leak. The shops are quoting $250- $300 to replace but I can buy a water pump at the auto parts store and install myself for less than $100 but I don't know what all is involved with this repair or if I should try (my only experience with car repair up to now is recently replacing the alternator). If anyone has done this please let me know what you think. thanksHow difficult is it to replace a water pump on a 1990 mercury Grand Marquis?1. Disconnect the negative battery cable.



2. Drain the cooling system. Remove the air inlet tube.



3. Remove the fan shroud attaching bolts and position the shroud over the fan. Remove the fan and clutch assembly from the water pump shaft and remove the shroud.



4. Remove the air conditioner drive belt and idler pulley bracket. Remove the alternator and power steering drive belts. Remove the power steering pump and position aside, leaving the hoses attached. Remove all accessory brackets that attach to the water pump.



5. Remove the water pump pulley. Disconnect the lower radiator hose, heater hose and water pump bypass hose at the water pump.



6. Remove the water pump attaching bolts and remove the water pump. Discard the gasket.



To install:



7. Clean all old gasket material from the timing cover and water pump.



8. Apply a suitable waterproof sealing compound to both sides of a new gasket and install the gasket on the timing cover.



9. Install the water pump and tighten the mounting bolts to 12-18 ft. lbs. (16-24 Nm).



10. Connect the hoses and accessory brackets to the water pump. Install the pulley on the water pump shaft.



11. Install the power steering pump and air conditioner idler pulley bracket. Install the accessory drive belts.



12. Install the fan and fan clutch assembly and the fan shroud.



13. Adjust the accessory drive belt tension; refer to .



14. Connect the negative battery cable and fill the cooling system.



15. Run the engine and check for leaks.



http://repairguide.autozone.com/znetrgs/How difficult is it to replace a water pump on a 1990 mercury Grand Marquis?It's a rear wheel drive car with the water pump mounted on the front of the engine toward the radiator. So if you go to the library any read the chiltons or motors manual procedures on how to replace the water pump, you probably have to remove the radiator fan blade assembly to get at the water pump. Some fan belts will also have to be removed. You can end up doing the job twice if the new water pump gasket doesn't seal properly due to antifreeze leaking out of the engine block while your installing the new gasket and sealer. Park the car with the engine facing up a hill to prevent that. I'd have it done at a shop. It's worth paying a shop unless you really want to get into major repairs.How difficult is it to replace a water pump on a 1990 mercury Grand Marquis?if you have the right tools it not to hard make sure the old gasket is clean off the engine before installing the new pump use a light coat of gasket sealer with itHow difficult is it to replace a water pump on a 1990 mercury Grand Marquis?you can make it even easier by purchasing a hayne's manual for your car when you buy the water pump. you will need it anyway so you can have the proper torque specs and sequence when reinstalling the new water pump. so if you don't have a torque wrench you will need to rent one. the first step of course will be to drain your cooling system. then use masking tape and a sharpie to number any connectors or hoses you have to remove to access the water pump. once the old one is off make sure to clean every trace of gasket material from the mating flange. then when you are ready to reinstall put a thin coat (use you fingers to spread)of rtv silicone to each side of the new gasket this will help hold in place. then here's where you will need the book insert the bolts and tighten them in sequence shown to the proper torque unless you want to chance cracking the new pump housing. on a car this old if it has not already been done now would be a good time to replace hoses (esp. if they are soft) and your thermostat since you've already got the cooling system drained. once everything is reassembled start the engine and begin pouring in the new coolant, if there are any bleed screws open these it's very important to get all the air out of the system if there are no bleed screws you can leave the cap off the radiator or expansion tank (you'll need to anyway) since one you think its filled when the thermostat opens its all gonna drain down and you'll have to top it off again. here is a good time to pay attention as it approaches normal operating temp be ready to start pouring as soon as the level starts to drop that will help keep more air from getting in. any questions feel free to e-mail me

How to install a water pump on a 2000 Jeep Grand Cherokee Laredo V6 4WD?

I would like to know how to install a water pump on a 2000 Jeep Grand Cherokee Laredo. Is it difficult? I can do minor repairs myself (window regulators, o2 sensors, etc..) would this classify as a simple repair? The more details the better! Any websites with some pictures would be appreciated too. ThanksHow to install a water pump on a 2000 Jeep Grand Cherokee Laredo V6 4WD?if your engine run's side to side it will be a lil bit harder cuz of clearence but if the serp belts at the front it should be alot easyer

How to change a water pump on a 1994 Saturn SL2?

I am having problems with my car. I need to know how to change the water pump on it.How to change a water pump on a 1994 Saturn SL2?Its Easy!! Remove the battery, windshield washer tank, and carbon cannister. put blocks under your engine to support it when you take the right side motor mount off (right side of the CAR),



Remove the valve covers , remove the belts, then the hoses, timing belt cover, and mark your timing belt-locations/placement of the cogs.



Remove the right side motor-mount.



remove the timing belt with Saturn tool number F-1210039-AF-000 to loosen the tensioner without losing the innards of the tensioner.



Using your %26quot;L%26quot; shaped TORX wrenches (#35) remove the Water pump,.



Replacement is the reverse, dont for get to buy all new gaskets, also for the Valve cover too!!



Easy!How to change a water pump on a 1994 Saturn SL2?Wow! Worst best answer I have seen here. I have the H20 pump from my 94 SL2 in my hand. All I had to remove was the tire, the plastic splash guard, the serpentine belt and the coolant. That year Saturn has a timing chain. Not a belt. I needed no special tools either. Just common wrenches and sockets

Report Abuse

How to change a water pump on a 1994 Saturn SL2?TAKE IT TO A QUALIFIED repair shop you have to mess with the timing on some of those damn saturns to change the water pump . Alittle hint if you have over 70,000 miles on that engine get a new timing belt put on it as well . if that belt breaks it will bend every single valve in your head , and its very pricey to have repaired. not to mention all the bolts that hold every thing together are single use only. it states that in black and white in a saturn repair manual.

land lord kick

growth of thin hair

How long should a water pump last?

My husband has a 78 t-bird and it has steam comming out of it. He replaced the water-pump 2 to 2 1/2 yrs ago. The warranty was only for 1 year should it need to be replaced this soon?How long should a water pump last?You didn't indicate from where the steam is originating. It could be from the radiator, radiator cap, coolant reservoir, cracked manifold, gaskets, hoses, etc, etc, etc, in which case, the water pump may have nothing to do with the problem (of course, a fault pump may CAUSE the problem, but, without more information, it's impossible to give you a specific answer).



As far as how long water pumps last, it depends on the manufacture, whether it's new, used, or remanufactured, how much and how %26quot;hard%26quot; the vehicle is driven, etc etc etc. Generally speaking, a brand new water pump should last at least 10 years or 100,000 miles.



Good luck!How long should a water pump last?It's possible. It depends on how many miles you've put on the car since then. The Water pumps on the older cars are not designed to go for more than 30-40K miles. Also if the car has been sitting the seals might have dried up a bit allowing for the steaming effect.How long should a water pump last?Years is the wrong way of looking at it. You should look at in mileage. And it depends on if the replacement was a new or re manufactured. Remans last about 1/3 the time (or mileage) of a new. Be sure to check the entire cooling system and fix the problem. I've seen people replace entire cooling systems ( radiators, water pumps, thermostats) only to find out it was a head gasket.How long should a water pump last?unless the pump is leaking it is not the problemHow long should a water pump last?there is no set time a water pump will last, I have seen them last 200,000 miles and I have seen them last 4,000 miles.

Do you have to turn off the water pump when you put drywall into the basement?

A friend of mine was putting drywall into Person A's basement. Person A later called and accused my friend of turning off the water pump. It had rained after the drywall was put into the basement. Another friend of mine said that turning the water pump off is not needed when putting drywall into the basement. How can we prove that it is not my friend's fault for messing up the basement? Any suggestions?Do you have to turn off the water pump when you put drywall into the basement?Did your friend turn off the water pump? If yes,and forgot to turn back on,is his fault the water stayed in basement.If no,then wasn't his fault.



Should not have to even touch the water pump to hang drywall.One has nothing to do with the other.Do you have to turn off the water pump when you put drywall into the basement?Drywall should have nothing to do with the water pump, if it rained then it was probably some leak in the basement.Do you have to turn off the water pump when you put drywall into the basement?Just tell your friend to not admit that he/she turned off the water pump (assume you mean %26quot;sump pump%26quot;).



I can't think of a reason to turn off the pump, unless maybe it was plugged into an outlet that was needed for lighting or power tools. In that case, it would have been good business to restore the pump's power.



As they say %26quot;Mistakes were made!%26quot;



One option would be to let the case go to small claims court, where the plaintiff will need to prove that your friend turned off the pump.Do you have to turn off the water pump when you put drywall into the basement?Guessing you mean a sump pump. Did your friend unplug the pump to put the drywall around the outlet and forget to plug it back in?Do you have to turn off the water pump when you put drywall into the basement?Assuming the %26quot;water pump%26quot; is a sump pump. The only scenario I can think of where the sump pump would be turned off while hanging drywall is if the drywall was being hanged around the electrical outlet. In that case, you absolutely would need to unplug the pump.



Of course, it is a little irresponsible (or lazy) of Person A to not check the finished product and ensure that everything is back to normal.Do you have to turn off the water pump when you put drywall into the basement?if your friend turned the sump pump off he is an idiot.theres no reason to turn the pump off,its supposed to stay on all the time.what does putting drywall in a basement have to do with the sump pump anyway????

sump pumps are installed to pump out ground water and rain overflow from the drain tile,if the pump is turned off,the basement will flood.Do you have to turn off the water pump when you put drywall into the basement?if your talking about a sump pump then there's no way. he may have unplugged it by accident and not even been aware

How much should repairing a water pump leak cost?

I know this is a pretty broad question, but I have a really old car and it may not even be worth it to take it to a garage. It's a '95 Subaru Legacy wagon. It's severely leaking water (especially when the radiator cap is off), and it looks like the leak is from the water pump.



Any ballpark of how much this could wind up costing at a garage would be appreciated.How much should repairing a water pump leak cost?As with any off-shore company owned car, replacement parts are expensive. To give you an idea autopartswaerhouse.com has re-manufactured water pumps from $60. - $72.00 for your particular car. A local Subaru dealer ship would really sting you if you had it repaired there as they most likely install a brand new water pump.



A private mechanic could change the pump within an hour. You could possibly find a replacement pump locally at Carquest, Advance Auto and Auto Zone as a last resort.

What size of a water pump do I need for a 50 meter bolehole?

I have sunk a 50 meter bolehole with water from 9 meters all way down. I want to buy a water pump. I would like to know how big the pump should be. I want to have as much water as possible.What size of a water pump do I need for a 50 meter bolehole?You mean borehole? You mean electric pump in horspower or fuelfed engine pump?

An electric submersible pump higher than 5 hpWhat size of a water pump do I need for a 50 meter bolehole?The determining factor in how deep a pump can go is really head pressure. You need a pump that develops enough head pressure to lift the water the height you desire.



Water is about 1 atmosphere of pressure for 10 meters. Therefore you would need a pump to generate about 5 atmospheres or 75 psi of head pressure to lift from 50m to surface. Since you say you have water at 9 m depth, you really would only need 1 atm or 15 psi of head pressure, however, do you anticipate drawing the water level down to the bottom then look for the 75 psi rating.



As far as volumo of flow, get whatever suits your needs as long as it fits in the bore hole.What size of a water pump do I need for a 50 meter bolehole?The limit is in the well, (bore-hole), not the pump.

The 'head` is only 9 meters + whatever your

utilization requires .

You should run a test.

Pump the bore-hole down a meter or so and

measure how long it takes to come back to the

9 meter level.

This, with the diameter of the bore will give you

the capacity of the well.

Then size your pump for that GPM at the pressure you require.

How long should the Second timing belt & water pump last on a '98 Mitsubishi Eclipse?

This car is the GS (non-turbo) model with the larger 2.4 L engine and now has 140,000 miles on it . The owners manual says to change the first one around 60k - I did that one on time. But, then I've heard that the parts that are put in at 60k last alot longer than the originals. How long should they last? And, when do I need to change the timing belt %26amp; water pump again? Thank you!How long should the Second timing belt %26amp; water pump last on a '98 Mitsubishi Eclipse?It's time for replacing another timing belt and water pump, the sooner the better. This should have been done at 120,000 miles. You should go with what the owner's manual says if you want to keep your car for a long time. when timing belts breaks, rods and pistons will be F***** and you will have to dole out lots of dough. spend a little now or a lot later. to avoid being double charged for labor when replacing timing belt you should consider changing water pump too as water pump and timing belt are located in the same area.How long should the Second timing belt %26amp; water pump last on a '98 Mitsubishi Eclipse?I would definately consider replacing the timing belt soon. Japanese cars normaly need the timing changed sooner than other autos. The enginse are made of lighter metals so if the timing breaks it will bend up your rods and dent up your pistons which is really expensive and time consuming to get fixed. It is better and cheaper to be safe and early than the alternative. Not sure about the water pump however.

Good luck.How long should the Second timing belt %26amp; water pump last on a '98 Mitsubishi Eclipse?It's best to do the timing belt every 60,000 miles as called for in the vehicle maintenance charts. I would replace the water pump at 120,000 miles if it makes it that long. Don't forget to change the timing belt pulleys and hydraulic tensioner which I prefer to do every belt change to avoid come backs. The 420A motor is well known for the bad head gasket design from the Chrysler factory so make sure to check for oil leaks before doing the work or you will have to repeat the belt work when replacing the head gasket.

solar dermatitis

sexy myspace

How much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?

I wanna change timing belt and water pump.

But i don't know how much it is.

I live in perth in Australia.



How much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?



Can you recomend the mechanic shop?How much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?i cant help you with prices in perth but here in melbourne i would do the job for around $600 all up maybe this will give you an idea of costsHow much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?I can't recommend any shops for you, too far away.



Ask family or friends for good repairers.



The belt can be purchased as a kit, with seals and tensioner included. The kit will cost about $250.



The waterpump will cost about $200 for a genuine unit, or about $100 for an aftermarket one.



Just add 5 hours of labour ( at whatever rate ), and the cost of coolant.



This is a rough guide for a V6 engine MagnaHow much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?Depends on if your engine is the 4 or 6 cylinder model.

The V6 will cost more as you have twice as many cams to time and the water pump sits deep in the engine valley.How much doest it cost to change timing belt and water pump for Mitsubish Magna 1997 sedan?$800 US parts and labor

How many labor hours to replace a water pump on a 1999 monte carlo?

I am considering the purchase of a 1999 Monte Carlo, however it is in need of a water pump. I am getting conflicting quotes from local mechanics. Can anyone tell me what the actual book time is for this repair?How many labor hours to replace a water pump on a 1999 monte carlo?the book time is 1.2 hrs, I would have them put a drive belt on the car at the same time! you do not have a timing belt just a alt belt!How many labor hours to replace a water pump on a 1999 monte carlo?You can call your local Dealership and they will give you the labor for this repair.

Most all shops use the Chilton Labor Guides for labor time on repairs.

Make sure you shop around for good part prices.

I advise my clients to find this information Labor/parts price.

then they can call around and shop for the best price,

if the labor cost is right but the part is outrageous,

then supply the part (do not tell the shop that you will be supplying the part or they may try to raise the labor price).

good luckHow many labor hours to replace a water pump on a 1999 monte carlo?Depends on what engine it has. If it has a 3.8L it is about 3.5 to 4 hours.



If it has the 3.1L it is about 1.5 hours.How many labor hours to replace a water pump on a 1999 monte carlo?i believe the book time is less than an hour.How many labor hours to replace a water pump on a 1999 monte carlo?you shoudl replace the timing belt while your doing the water pump tooHow many labor hours to replace a water pump on a 1999 monte carlo?2.5How many labor hours to replace a water pump on a 1999 monte carlo?depends what motor you have and 3.8 isnt one of them you got 3.4 or 3100

Where is the water pump on a 2003 svt cobra located?

I need to replace the water pump but i dont know where to find it, where is it located and how do i remove it? thank you.Where is the water pump on a 2003 svt cobra located?its just to the left of center and its in the very front of the engine compartment just behind the radiator. i own a 2004 cobra and mine failed and I did not know it. i was doing some high speed passes and It caused me to cook a cylinder. I am so pissed.



additional--

sorry, but I do not know how to remove it.Where is the water pump on a 2003 svt cobra located?it should be on the front of the engine behind the fan thats where most of them are on v8s there should be a belt you have to take off then a number of bolts then smake sure you have all of the old gasket removed and slap it all back together and fill with coolentWhere is the water pump on a 2003 svt cobra located?follow your radiator hoses to the engine, that'll lead you right to it

What RPM is required to operate a car water pump?

I know that the water pump is belt driven, so it would be easy to connect it to my bicycle. What I am wondering is if I can pedal fast enough to make it work. Does anyone know how fast I would need to pedal to operate the pump?What RPM is required to operate a car water pump?Mechanical water pumps will move water with any rotation, provided it's a sealed system and there are no obstructions. The flow rate will be determined by the RPM of the water pump. This is proportional to the pulley sizes of the drive pulley to the water pump pulley.



600 RPM for a water pump at idle is sufficient for the cooling system design and the engine heat load at idle. Without knowing the specifics of your application, it would be hard to tell how fast you would need to pedal.What RPM is required to operate a car water pump?Pretty fast. Engines operate at 600-6000 rpm and the pump pulley is a little smaller than the drive pulley, so it is spinning even faster.

That said, 600 rpm is plenty fast enough. You can attain that easily by applying pulley to rear tire tread, raising tire off ground and pedaling. To apply bike chain to pulley would give a disappointing water flow.What RPM is required to operate a car water pump?Idle speed of car at minimum is around 600 RPM.Too fast to pedal.

How do I create a working water pump for a stage production?

I need a water pump for a production of %26quot;The Miracle Worker.%26quot; Is there a way I could put a working pump on stage for a relatively cheap amount of money (working with a small high school drama budget). It would be great if there was a way to catch to water as well so that we could avoid messy cleanup. Thanks!How do I create a working water pump for a stage production?If you want several useful ways that won't break in the middle of production, I suggest asking a real engineer.

can dogs eat celery

install spare clear card

How do you know if your water pump is failing?

I'm leaking coolant and I cant see where it is coming from. Its only when the car is running. My serpentine belt is sqealing also. What could cause this? It all happened around the same time. I'm not sure what it is cause I can't see it, but i think it is the water pump. could you tell me some symptoms of a failing water pump?



Also the car stays cool, its not overheating one bit, but I have to fill the coolant with like 1/2 gallon of coolant every two days.How do you know if your water pump is failing?Your car has the early symptoms of a water pump that is going out. It is the %26quot;bearings%26quot; that is slowly going out. It may not heat up right now but it probably will soon. Get it checked by a professional!How do you know if your water pump is failing?Sounds like a leaky radiatorHow do you know if your water pump is failing?It sure sounds like the water pump. Thats the same synptoms I had 2 years ago, when I had to replace the water pump on my van.. You might as well spend the money on one now, or you'll be a slave to buying and pouring coolant forever. You can get a good used one at a salvage yard for a reasonable price. Avoid a major dealers parts dept at all costs. They will rape you.How do you know if your water pump is failing?Your description is that of a failing water pump. Grasp the fan impeller housing and move it horizontally and vertically. If you can move it more than 1/4%26quot; then it is water pump time. Get a rebuilt one at a parts store or if you prefer quality get a new one from the dealership. You pay a little more but you get the best quality. Avoid the suggestion of using used parts. You will just be doing the job over very soon.How do you know if your water pump is failing?In in my experience, waterpump's failure is leaking (before it stops working as a pump), so that might be why. And since the water pump may be turned by your serpentine belt then maybe the belt is getting wet and squeeling (or maybe you just need a new belt for that old beater you have there, besides a water pump). Sometimes water pumps are not visible because they are driven by the timing belt (like in a 3.0 Chry/Dodge Engine in a minivan). But I suppose the water could be leaking under that and eventually coming out on your belt. If the water pump is being powered by the timing belt there should be an inspection cover somewhere you can remove to look down in there.How do you know if your water pump is failing?those are the symptoms you better go have your car checked before you mess up the engine and then it's really going to cost youHow do you know if your water pump is failing?Leaky radiator or hose.How do you know if your water pump is failing?yes sir the squealing your hearing is the bearings in the pump going bad.if its more of a puddle in the morn or whatever time it sits the longest, its your pump. when the engine is at its coolest everything expands,hence leakage. also, the more i think, the squealing cud be just a loose belt or an a/c clutch fan going bad too.How do you know if your water pump is failing?Some other things to look for or check, does the pump make noise at all, pull or move the hose around and watch for the coolant to increase in what leaks then it might be the hose at the clamp connection. now if you need to replace it you never want to buy a salvage yard pump, you can get a rebuilt one or brand new one for a fair price, i would guess at about 30 to 50 dollars and a core charge, to make this repair you will need to take the front of the engine apart up to and including the alternater, a/c compressor, power steering pump ect. some or all of these components may have to be removed, there are also some procedures and precautions that you will need to be aware of to ensure a proper installation, function, and not have any leaks. if you are new to auto repairs i would let someone with experience do the job or take it to your mechanic to make the repair. good luck!!How do you know if your water pump is failing?Park the car on a clean surface, open the hood, start the engine and then watch for leaks. Most water pumps have a weep hole at the bottom, coolent could be getting on the belt making it slip a squeal. If you can't see get a flashlight and look. Sometimes when a water pump goes bad, the bearing will fail and make noise the shaft will be loose. Or you can take your car and have the cooling system pressure checked, and the leak will show up.

How to make a water pump for an indoor waterfall?

hello,



I am trying to make an indoor waterfall for a party. It would ideally be about 10 feet tall, so I need to make a pump that would vertically raise water that collects at the bottom to the top to fall down again. Does anyone know of any websites/books/other sources that could tell me how to build my own pump, especially for someone like me with no experience with this kind of thing?How to make a water pump for an indoor waterfall?Building a submersible pump would cost more than purchasing one. You can buy submersible pumps from home improvement stores.

You could use an external pump with a suction and discharge, but you would have to house this in a cabinet that you can access.How to make a water pump for an indoor waterfall?home depot or lowes get a free standing sump pump mount a 10 foot pvc pipe to it and you will be just fineHow to make a water pump for an indoor waterfall?depending on the amount of water you want to flow you could use a fish tank type pump or a submersible type that flows a garden hose size you should use a ball valve to regulate the water flow/pressureHow to make a water pump for an indoor waterfall?If in the states, I would go to Harbor Freight and buy yourself a submersible water-pump, they are fairly cheap and I would spend any top-dollars for it unless you want it to last forever-you will takes this apart once the party is over, right?



You can use flexible line for fish tanks (ever an old garden hose and hose-clamps would work) to attach one end to the pump, and one end to the top of your waterfall. I would make sure you have a basin deep enough to handle the fluids, it will take some serious volume once the pump is running, enough fluid to fill the line, and the basin %26amp; remember once you turn off the pump all that liquid will settle in the basis so make sure it wont over-flow and make a mess!



have fun

How do i replace a water pump on a 1992 chevy cavalier?

I think I need to replace the water pump. water is gushing out the weep holes when I add water to the radiator. I don't have the money to take my car to an auto shop.How do i replace a water pump on a 1992 chevy cavalier?remove the top motor mount, release the tension on the belt tensioner by turning the center bolt counterclockwise, remove the serpentine belt (take note how it is routed), take the bolts out of the water pump that is holding it on. be sure to remove all of the old gasket.

put rtv sealent on the new gasket and the block surface, install in reverse order.



note: you might need a pry bar to line the motor up to reconnect the top motor mount.

How do you change out a water pump for a 96 z24 cavaliar?

Need to know how difficult it is to change out the water pump on a z24 chevy Cavaliar. Do I need special tools etc. Can I do it from the top or do you have to get underneath the car.How do you change out a water pump for a 96 z24 cavaliar?Here are the instructions, it really doesn't require any special tools but it is not an easy pump to change, I would recomend having a pro do the job. The pump on your engine is run from the timing chain not a belt making replacement quite difficult. It will require work from the top and bottom of the car, GM recomends using a car lift. If you decide to try this do yourself a favor and get your hands on a service manual. To give you an idea of the complexity of this job, Mitchell labor time guide allows 5.6 hours for an expierenced tech to replace your water pump. REMOVAL





Negative battery cable.

Drain and recover coolant.

Oxygen sensor connector.

Upper exhaust manifold heat shield and heater hose quick connect from heater outlet pipe.

Coolant inlet housing bolt through exhaust manifold.

Raise vehicle.

Exhaust manifold brace to manifold bolt. See Exhaust System.

Manifold to exhaust pipe bolts and heater outlet pipe bracket to bans bolt.

Coolant inlet housing assembly to water pump cover bolt.

Exhaust pipe from exhaust manifold. See Exhaust System.

Pull down and back on the exhaust pipe to disengage it from the exhaust manifold.

CAUTION: DO NOT rotate flex coupling more than 4 degrees (step 11) as damage may occur.



Coolant inlet pipe from oil pan. Leave the lower radiator hose attached and pull down on the coolant inlet pipe to disengage it from the water pump. Leave the coolant, inlet pipe hanging.

Lower vehicle.

Brake vacuum pipe from cam housing. See Brakes and Traction Control.

Exhaust manifold to cylinder head retaining nuts.

Exhaust manifold, seals and gaskets. See Exhaust System.

Front timing chain cover. See Engine.

Timing chain tensioner. See Engine.

Water pump cover to cylinder block bolts.

Water pump assembly to timing chain housing nuts (3).

Water pump and cover assembly.

Water pump cover to water pump assembly bolts (5). Clean all sealing surfaces.

CAUTION: Prior to installing water pump read the entire procedure. Pay special attention to the tightening sequence to avoid part damage and to insure proper sealing.



INSTALLATION





Water pump cover to water pump assembly and install bolts HAND TIGHT.

Cover to block bolts hand tight.

Pump to chain housing nuts hand tight.

Lube Oaring on coolant inlet pipe with an anti-freeze solution and slide pipe into water pump cover install bolts hand tight.

With specified gaps, torque in sequence as follows:

Pump to chain housing nuts. Tighten nuts to 26 Nm (19 ft. lbs.) .

Pump cover to pump assembly. Tighten bolts to 14 Nm (124 inch lbs.) .

Cover to block, bottom bolt first. Tighten bolts to26 Nm (19 ft. lbs.) .

Coolant inlet pipe assembly to cover. Tighten bolt to 14 Nm (124 inch lbs.) .

Exhaust manifold and new gaskets. See Exhaust System.

Exhaust manifold to cylinder head retaining nuts.

Brake vacuum pipe to cam housing.

Raise vehicle.

Index exhaust manifold bolts into exhaust pipe flange. See Exhaust System.

Exhaust pipe to exhaust, manifold, land, heater outlet pipe bracket to trans.

Turn both exhaust bolts in evenly to avoid cocking the exhaust pipe and binding the bolts. Turn bolts in until fully seated.

Coolant inlet pipe to oil pan. Tighten bolt to 26 Nm (19 ft. lbs.) .

Timing chain tensioner. See Engine.

Timing chain cover. See Engine.

Lower vehicle.

Exhaust manifold brace to manifold bolt.

Manifold to exhaust, pipe nuts. See Exhaust System.

Position heat sleeve on heater hose, then heater hose to the heater outlet pipe. Inspect quick connect retainer, pull heater hose to verify connection.

Upper heat shield to the exhaust manifold.

Oxygen sensor connector.

Fill radiator with coolant.

Negative battery cable. Tighten bolt to 16 Nm (12 ft. lbs.) . Inspect for leaks.How do you change out a water pump for a 96 z24 cavaliar?do it from the top. it only took me 20 minutes,to do.

How difficult is to install a water pump on a 1996 Dodge Shadow?

Some guy is offerering me to buy his 96 Dodge Shadow for 600, only thing is the water pump is bad and he'll throw in the replacement, if i fix it myself. Would it be worth it?How difficult is to install a water pump on a 1996 Dodge Shadow?Depends on which motor. the 2.5L engines are not that bad since it is on the outside of the engine. However, the 3.0L engine is a little worse since it is run by the timing belt.How difficult is to install a water pump on a 1996 Dodge Shadow?If its located on the out side, its as easy as taking off the belt unbolting it, and breaking it loose to take it off.Its pretty simple just make sure you lubricate the O-ring with some type of silicone grease before installing it back in and tighen down the bolts good.How difficult is to install a water pump on a 1996 Dodge Shadow?Have you ever tried anything like this before? Do you have the tools necessary? You might do yourself a favor and look in the repair manuals sold in auto stores to see what the job entails. Good luck!

howtocuddlewithyourboyfriend

advice about asking a girl out

What is the easiest way to replace a water pump in a 01 chevy cavalier?

I have 100,008 miles on this car and just then water dumped out of my chevy like it was a flood! It slow leaks water when it's off and pours like the nile when it's idling.

I am looking to know that the water pump is the right diagnosis, what tools are required to, and how to replace this part myself. Reason: Cause I'm trying to save on about $450.00 of labor. The part is only $23.00. :P



Any helpful answer is appreciated, thanks.What is the easiest way to replace a water pump in a 01 chevy cavalier?depends on the engine size.the small one takes a few hours and z engine takes almost 7 hours to do.What is the easiest way to replace a water pump in a 01 chevy cavalier?Actually, I'd like to add that it is not the Z and is a 2.2L sohc. The hoses all are fine and %26quot;non squishy%26quot;, and the water pump assembly to its 'bracket'[?] is perfectly viewable. I've already been quoted as the cheapest at $260.

Report Abuse

What is the easiest way to replace a water pump in a 01 chevy cavalier?If you had a ramp to drive it up on, it would help other than that.. a garageWhat is the easiest way to replace a water pump in a 01 chevy cavalier?There is no easy way to repace anything in a car today. Just look under the hood and see how cramp everything is . A lot of disassembly is in order to put in the new water pump.What is the easiest way to replace a water pump in a 01 chevy cavalier?It should not cost 450 to replace a water pump - maybe about 250 maximum.



However, if you know nothing about cars, either make the choice to take it to a mechanic (towed) or dump it.



BTW, it may not be a water pump, but a hose.What is the easiest way to replace a water pump in a 01 chevy cavalier?If you got 100,000 mi. out of a cavalier, count yourself VERY lucky and then burn it!

How do you replace a water pump in a 1995 Toyota Camry?

My Camry is overheating and I am assuming it is the water pump. I already changed the thermostat and that was no help. When I turn the heater on to cool off the engine, it blows cold air or the temp of the air outside most of the time and seldomly hot air. I bought a water pump, but I am not sure if this is something I can do?How do you replace a water pump in a 1995 Toyota Camry?Got to give you credit Crystal for even thinking of tackling this. You already did the thermostat, good for you! It can be a difficult to replace the pump. You have to remove belts and unless the new pump has a pulley on it you will have to take the pully off the old pump. You ought to get a Haynes or Clymer repair manual for the Camry and follow it step by step. If you are going to go through with it. BUT.... it might not be the waterpump. Whenever a modern car overheats the 1st thing you want to rule out is a blown head gasket. Camry's are not known for blowing head gaskets though. It could be several other things. Like for instance the fan not turning on. You must put a diagnosis to the problem before you start replacing things. I found a Camry Forum for you. Ask some question? Ask how to know if the head gasket is blown? Also search the question/answers for a problem like yours. The waterpump might be tough to change. http://www.camryforums.com/m_4566/tm.htm Good Luck.How do you replace a water pump in a 1995 Toyota Camry?I don't know how YOU do it, but as for ME, I hire a mechanic.How do you replace a water pump in a 1995 Toyota Camry?Step 1: Find a manHow do you replace a water pump in a 1995 Toyota Camry?get it fixed at a mechanic shop and make sure ur getting a deal ; professional work is done by pros and you get what u pay for less time and less worry and less mistakes that can cost money by guessing buying wrong parts and gaskets

How do i turn my water pump on automatically via a pressure switch?

I have installed a large water tank that collects all rain water. I now wish to connect a pump to this which is then connected to a standard hose. I would like to achieve a reasonable pressure equal to mains pressure. I can purchase a second hand shower type pump and adapt it however this pump does not have a pressure switch connected. A flow switch would not work as if the end of the hose is higher than the tank no flow therefore I need a pressure switch so when I open the hose the water flows then when I shut it the water stops. What type of pressure switch do I need and any idea's where to get it fromHow do i turn my water pump on automatically via a pressure switch?I would set the system up somewhat like a well. Two places to put the pump 1. in the tank and pump up or 2. outside the tank and pump water into the tank to make water come out of the tank or just suck out of the tank. Watch out for a thing called Net Positive Suction Head and if the pump is self priming. NPSH is the amount of water required over the pump inlet for it to work. Self priming is required to get the air through the pump and start pumping water. If the tank is above ground and the pump is at ground level make sure you put a shut off valve between the pump and the tank in case you have to work on the pump. Next you need a check valve to make sure the water does not run back into the tank when the pump is shut off. Then I would buy a well tank like mentioned in the other answers that has a bladder and pressure switch already on it. The purpose of this is to keep from burning up your motor by starting and stopping it. Last but not least, DO NOT HOOK THIS UP TO YOUR DOMESTIC WATER SYSTEM. The rainwater tank will eventually become contaminated with all kinds of things that you do not want to mix with your drinking water. Okay for yard things but not for drinking. If you do hook it up to the domestic water system the local folks will want a back flow preventer on your system.

Extra information, Put a pressure gauge on your city water and find out the pressure. If it is in PSI pounds per square inch and other things are rated in feet of head the conversion is 14.7 PSI or PSIA is equal to 34 feet of head.How do i turn my water pump on automatically via a pressure switch?well, you can use a level float, or rig a water pump via a manual switch with a low level safety cutout.



use 12v, not mains power...



i suppose teh simplest way is to drop a pond pump into the tank, and flick a switch for on...



or seal teh tank, and pressurise it with air, which will displace water via a tube which connects to the hose.How do i turn my water pump on automatically via a pressure switch?You need to purchase an expansion tank that is typically used in household, well fed, water systems. The expansion tank has a bladder in side of it. As the predetermined pressure is reached, the pressure switch will shut the pump off.How do i turn my water pump on automatically via a pressure switch?Someplace like www.graingers.com will have the pieces you need but I think it's going to cost more than you expect. The switch you need is nothing special and just needs to be adjustable in the pressure range you want and be able to carry the starting current of the pump. You want to use the common and normally closed terminals. That will give you a closed circuit with no pressure and open when the pressure comes up to the setpoint. You can make your own pressure tank from a used 25 lb disposable freon bottle or similar. Drill a hole and install a metal tire stem in the tank so you can refill it when all the air has been absorbed. You will be able to tell by how often the pump starts and stops when you aren't using any water. Unless you are using a really long hose you can probably get by with 25psi or less, the lower pressure won't need as expensive a pump.How do i turn my water pump on automatically via a pressure switch?I have recently completed an assignment in college in which i had to reverse engineer a pressure switch for a water pump. the company it was made by was Italtecnica. You can find them on the internet

Want to know if my water pump is good or bad. How do I tell without doing all the labor to remove it?

How do I check my water pump without pulling it?Want to know if my water pump is good or bad. How do I tell without doing all the labor to remove it?1) Noisy bearing

2) Loose bearing-----------Pulley wiggles around

3)Leaks water

Any of these symptoms replace it............UJNWant to know if my water pump is good or bad. How do I tell without doing all the labor to remove it?What are the symptoms and what is the make/year of your car?Want to know if my water pump is good or bad. How do I tell without doing all the labor to remove it?Look at the ground. If your coolant is hitting the ground, it's bad. If not, it's good.



That's the easiest diagnosis there is.Want to know if my water pump is good or bad. How do I tell without doing all the labor to remove it?leaks or noise. If you are overheating, check thermostat.

How do I remove the water pump drive pulley on a 98 Cadillac Deville?

This is not the tensioner pulley or the pulley on the water pump this is the pulley attached to the engine drive. I can not get it off and I need to in order to replace the head gasket. Please help.How do I remove the water pump drive pulley on a 98 Cadillac Deville?It should have 4 bolts in the center holding it in place

scene hair

so thin skinned

Our water pump quit working and I was wondering how to fix it?

I went to turn on the water in the kitchen and nothing came out. Figured it had to be the water pump because I didn't hear it kick on. How do I either turn the water pump back on or reset it?? I have never dealt with a water pump before! Help ASAP!Our water pump quit working and I was wondering how to fix it?You didn't say if it was above or below ground, so I will assume that we are talking above ground. First thing to do is check your circut breaker to be sure it is working properly and look for the reset button on the pump a volt meter will do this. Next check the regulator switch on the pump if this is bad it won't turn the pump off or on again use a volt meter. If this checks out then check the motor for power. You may have a loose connection or a short that is keeping it from working. By using a volt meter you will be able to track where the problem is. Another way to check to see if the motor is working is by disconnecting the wiring and wire the motor direct.Our water pump quit working and I was wondering how to fix it?I would start by checking your circuit breaker. Since you did not hear it start that might be the first place to check.Our water pump quit working and I was wondering how to fix it?with any luck maybe the breaker throwed, if that aint it then I guess maybe the pressure switch contacts need cleaning

probably have a burr or burned contacts, could be the motor but i doubt it. might be the starter capacitor has went out. thats the number one thang that goes wrong and the part is less than 10 bucks. see your well parts supplierOur water pump quit working and I was wondering how to fix it?check the breaker panel and see if any breakers have tripped or if you know which one it is reset it and try it again if that is not the case on the pump motor there maybe a red 'reset button' try resetting it good luck

How much to change a water pump on a 97 Mustang?

I need to know how much the average mechanic would charge to change a water pump.How much to change a water pump on a 97 Mustang?probly arowned 250-350. the water pump is located in the front of the engine so it is decently easy to get to. at a shop they will charge you about $100/hHow much to change a water pump on a 97 Mustang?your probably looking at 200-300 dollars its a decently easy repair though so im not sure

How do you replace the water pump on a 1994 Pontiac Firebird?

I have had an issue with my car overheating and replaced the water pump as of 9/23/05, but now I am getting the indication that the car is overheating again and I just can not afford to have the mechanic service it. I know the part is not expensive but the labor is just too much.How do you replace the water pump on a 1994 Pontiac Firebird?These are the best answer links I know.

Check them out and if you still need help feel free

to Email me for help.



http://www.ask.com/?o=312#subject:ask|pg - everything

http://www.info.com/ - 14 search engines

http://www.wisegeek.com/ - any question

http://www.autozone.com/ - diagrams,repair info,LOOK HERE

http://autoparts.411web.com/ - everything automotive

http://www.howstuffworks.com/ - how stuff works

http://www.thefreedictionary.com/ - dictionary

http://www.2carpros.com/index.htm - mechanics Q %26amp; A

http://www.streetracing.org/paris/dictio - terms

http://www.crutchfieldadvisor.com/S-CHQL - automotive audio/video etc.

http://www.partstrain.com/?id=doMecGRr - hard to find parts

http://www.mapquest.com/directions/ - directions %26amp; distance

http://www.carcarecouncil.org/index.shtm - basic car care

http://www.diynetwork.com/diy/autos_boat - DIY resource

http://www.autospeak.com/index.htm - for car enthusiasts

http://www.mendmy.com/answers.php?id=139 - fix anything

http://www.theautochannel.com/ - up to date auto news

http://www.motorera.com/ - old cars %26amp; definitions

http://www.autopedia.com/ - automotive dictionary

http://www.edmunds.com/ - automotive values



Web search for Forums for your car, they are very helpful.

Fereral, State, %26amp; Local governments have websites.How do you replace the water pump on a 1994 Pontiac Firebird?check that the cooling fan is operating properly. You may also want to replace the thermostat. Sometimes you may get an air pocket in the engine which must be worked out of the cooling system. the easiest way to do this would be to take the car on a SHORT trip around the block, then top off the coolant as needed.

How to remove the water pump on a 2001 Jeep Wrangler?

My brother needs to replace the water pump on his 2001 Jeep Wrangler. It is a 4.0L 6 cylinder, no A/C. Anyone know where he can find a step-by-step guide, or could provide one? Or which repair manual would be the best to purchase? Even if he could just get the order to remove things in to get to the water pump that would be great. Thanks!How to remove the water pump on a 2001 Jeep Wrangler?WJ Water Pump Replacement

4.0L I6



If you are like me, then replacing a water pump doesn't sound like that much fun, but you would rather do it yourself than pay someone else to do it.

Replacing the water pump on your WJ isn't going to be that hard, but a little help with the steps would probably be nice.

This write up will hopefully give you some pointers that could save you some time in the long run and make things a little easier for you.



1) Diagnosis. First thing you probably have noticed is that puddle of antifreeze on the ground in the morning. Check your hoses first and try to determine where the leak is coming from. If it is indeed dripping down the front of the engine block, check your hoses on the water pump and thermostat housing once again, just to be sure (no sense in doing more work than necessary here). If you are in the same boat I was, water and coolant is probably seeping out of the weap hole of the water pump. This is a good sign that your water pump is on its way out.



2) Replacement.



First drain your radiator. There is a petcock drain on the lower, passenger side of your radiator. It should have a rubber hose attached. I found that a little duct tape to secure the hose straight against the shroud makes it easier to drain it into a antifreeze bottle or container.



When you look at the top of your engine this is what you will see:







Not a lot of room at all between that fan shroud and the pulleys. You could possibly do the job with the fan shroud on, but I would HIGHLY recommend that you remove it - it will make your life a lot easier.



Before you remove the fan shroud, you should unbolt the fan clutch and fan from the water pump pulley. If your water pump pulley does not have any holes in it for a special tool, your best bet for removal is probably the hammer and crescent wrench. With the pulley belt still on, get a large crescent wrench and grip the large fan clutch nut. You will need to hit it several times to knock it loose. The trick to finding out which way the nut needs to turn is to watch which way the fan spins while the engine is on. Hit the nut the same way the fan spun. My fan spins counter-clockwise, thus, the nut broke loose by me hitting it counter clockwise. Once you break the large nut loose, unthread it all the way and set it down in the fan shroud.









To remove the fan shroud, you must first remove 2 radiator hoses. The top one is on the passenger side, just squeeze the clamps, pull it off and bend it out of the way. The lower one is on the driver's side, do the same.



Next, you will need to remove the 4 bolts securing the fan shroud. The picture below will indicate where they are located. Be sure to unplug the plug from the shroud as well.







You may wonder how they even got the 4th bolt screwed in during assembly, let alone how to get it back out. Some people have said that a socket with a few extensions did the trick, but with my WJ, there wasn't enough room between sheet metal and the bolt to get a socket in there. I found just by sticking my hand through lines and hoses and using a open ended wrench that I could slowly turn it out. When putting them back in, I took one look at the situation again, tested the shroud for secureness and then scrapped the 4th bolt. I figured it would be OK without it.



Once you get the 4 bolts out, you will need to work the fan shroud and fan, up and out the top of the engine compartment. Doing this will create a VAST space for you to work in.



This is a picture of the engine once you get the shroud and fan out of the way. Note, these pictures were taken on the reassembly process, so the water pump is new and the blue rubber cap is just to protect the new threads.







To get the old pump out, you will need to remove the the small hose connected to the metal tube coming out the top of the water pump. You can leave the intake hose on for right now and pull it out with the water pump. Once you disconnect the small hose, remove the 5 bolts that hold the water pump to the engine block. Be sure and keep track which holes they went in as they may be different sizes. In the picture below, you can see the old water pump, the pulley, and the metal tube as well as the locations of the 5 bolts.







Once you get the 5 bolts removed, you may have to gently tap the water pump itself with a mallet or hammer to get it to break free from the old gasket. Be sure to have a pan below the engine to catch coolant as more will poor out at this point.



When you have the old pump out, remove the pulley's 4 bolts and set it aside for reassembly. Also, remove the metal tube and set it aside as well. Examine it for corrosion and possible replacement. Mine was in good shape so I reused it on the new pump.



The next step I did was to remove and replace the thermostat as well. This is optional, but since you have it all apart, you might as well replace it since it's only a few bucks extra.



Remove the output tube as well as the small rubber hose and disconnect the sensor from the thermostat housing. There will be 2 bolts holding the housing on. Remove those and gently tap the housing to break it free from the gasket. More coolant will drain.







Be sure to THOROUGHLY clean all surfaces where new gaskets will be mated. Here is a picture of the thermostat housing after I cleaned its surface.







At this point, remove the thermostat (remember how it was positioned) and clean all gasket material from the thermostat housing area as well as the water pump. I used some degreaser and a exacto blade for the gasket material. Be sure and clean it really well and use a rag to wipe off any cleaner or coolant. Before installing new parts, make sure any old gasket material that may have fallen into the engine channels is removed.







Cleaned water pump surface.







Once you have reached this point, it is pretty much a matter of retracing your steps to install everything again. Insert the new thermostat in the same position as the old one was and reinstall the housing with the new gasket. Use a small ammount of RTV on the new gasket to hold it to the housing while mounting it. When installing the water pump, use a small ammount of RTV as well to hold the new gasket to the new water pump. Also be sure to install the metal tube before mounting the pump. I used some high-temp sealant on the threads. According to the FSM, torque the bolts to 17 ft lbs for the I6 and 30 ft lbs for the 4.7L V8.



Place the fan shroud back in the engine compartment with the fan inside just like removal. Thread the large nut back on until snug and gently tap it with the large crescent wrench. Don't try to force it tight, the engine turning the pulley will keep it on.

Reinstall the nuts to the shroud and all hoses and fill your radiator back up. Be sure to run your engine and purge the air from the system as well.



That's about it, overall the process isn't to hard. If you have any questions feel free to contact me.

Good luck on your replacment!How to remove the water pump on a 2001 Jeep Wrangler?You could try the Haines Manual. You can get this manual at your local parts house; also try your local library.How to remove the water pump on a 2001 Jeep Wrangler?VISCOUS FAN

REMOVAL

2.5L Engine Loosen but do not remove at this time, the four fan hub mounting nuts Fan Mount - 2.5L Engine

4.0L Engine The thermal viscous fan drive/fan blade assembly is attached (threaded) to water pump hub shaft. Remove fan blade/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using a suitable fan wrench loosen the fan drive Fan and Fan Drive - 4.0L Engine

Remove accessory drive belt. Refer to Belt Service in the Engine Accessory Drive Belt section of this group.

Some models with certain engines may require the removal of the fan shroud to remove the viscous fan drive. The fan shroud and fan blade/viscous fan drive should be removed from the vehicle as one assembly.

2.5L Engine Remove four fan hub mounting nuts Fan Mount - 2.5L Engine and remove fan/viscous fan drive assembly from vehicle.

After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.



WATER PUMP

CAUTION: If the water pump is replaced because of mechanical damage, the fan blades and viscous fan drive should also be inspected. These components could have been damaged due to excessive vibration.



REMOVAL

The water pump can be removed without discharging the air conditioning system (if equipped)



CAUTION: All engines have a reverse (counterclockwise) rotating water pump. The letter R is stamped into the back of the water pump impeller Reverse Rotating Water Pump - 2.5L Engine to identify. Engines from previous model years, depending upon application, may be equipped with a forward (clockwise) rotating water pump. Installation of the wrong water pump will cause engine over heating



Water Pump - 4.0L Engine



The water pump impeller is pressed on the rear of the pump shaft and bearing assembly. The water pump is serviced only as a complete assembly.



WARNING: DO NOT REMOVE THE BLOCK DRAIN PLUG(S) OR LOOSEN RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR.



DO NOT WASTE reusable coolant. If the solution is clean, drain coolant into a clean container for reuse.



Disconnect negative battery cable at battery.

Drain the cooling system.

2.5L Engine Loosen (but do not remove at this time) the four fan hub-to-water pump pulley mounting nuts Fan Mounting Nuts - 2.5L Engine

Fan and Fan Drive Mounting - 4.0L Engine



NOTE: The engine accessory drive belt must be removed prior to removing the fan.



Remove accessory drive belt.

4.0L Engine The thermal viscous fan drive/fan blade assembly is attached (threaded) to water pump hub shaft. Remove fan blade/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using a suitable fan wrench loosen the fan drive.

Remove power steering pump Power Steering Pump Attachment - 2.5L and 4.0L (Refer to Group 19 Steering)

WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) Hose Clamp Tool - Typical SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS



CAUTION: A number or letter is stamped into the tongue of constant tension clamps Clamp Number/Letter Location If replacement is necessary, use only an original equipment clamp with matching number or letter



Remove lower radiator hose from water pump. Remove heater hose from water pump fitting.

2.5L Engine Remove four nuts previously loosened and remove the fan blade assembly and pulley.

After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.

Remove the four pump mounting bolts Water Pump Remove/Install - 2.5L Engine and remove pump from vehicle. Discard old gasket. Note that one of the four bolts is longer than the other bolts.

Water Pump Remove/Install - 4.0L Engine



If pump is to be replaced, the heater hose fitting must be removed. Note position of fitting before removal.

INSTALLATION

If pump is being replaced, install the heater hose fitting to the pump. Use a sealant on the fitting such as Mopar庐 Thread Sealant With Teflon. Refer to the directions on the package.

Clean the gasket mating surfaces. If the original pump is used, remove any deposits or other foreign material. Inspect the cylinder block and water pump mating surfaces for erosion or damage from cavitation.

Install the gasket and water pump. The silicone bead on the gasket should be facing the water pump. Also, the gasket is installed dry. Tighten mounting bolts to 23 N路m (200 in. lbs.) torque. Rotate the shaft by hand to be sure it turns freely.

Connect the radiator and heater hoses to the water pump.

2.5L Engine Position water pump pulley to water pump hub.

2.5L Engine Install fan and four nuts to water pump hub. Tighten or nuts to 27 N路m (20 ft. lbs.) torque.

Install power steering pump.

4.0L Engine Thread the fan and fan hub into the water pump hub shaft

CAUTION: When installing the serpentine engine accessory drive belt, the belt MUST be routed correctly. If not, the engine may overheat due to the water pump rotating in the wrong direction. Refer to the Belt Removal and Installation in this group for appropriate belt routing. You may also refer to the Belt Routing Label in the vehicle engine compartment.



Install accessory drive belt. 2.5L Engine Tension drive belts. Refer to Accessory Drive Belt removal and installation in this group.

Fill cooling system with coolant and check for leaks. Refer to Refilling Cooling System in this group.

Connect battery cable to battery.

Start and warm the engine. Check for leaks.

How do you change a water pump on a 89 accord LXi?

I am using the Haynes Manual, however the book shows it very simply. When i look in the engine, i have to remove three belts just to get to the water pump. Replacing the pump should be relatively straight forward. Getting to it is the problem.



Reason why i want to change it, is because my car makes a rough knocking/gurgling sound when i accelerate or idle at a high rpm, and i think that my current water pump is clogged up and not allowing coolant to get through the engine block.



Any suggestions out there?How do you change a water pump on a 89 accord LXi?if you hear a knocking sound it might be the idler pulley, not the water pump. If it is the water pump it should have been replaced when you replace the timing belt at approx 55k miles. You have to remove the timimg belt to replace the water pump. It is a major repair bill if you have someone do it.How do you change a water pump on a 89 accord LXi?If the water pump was the problem, you would see the temperature rise on the engine. I doubt this is the problem. You should take the car to a mechanic to troubleshoot.How do you change a water pump on a 89 accord LXi?look guy if it's not leaking then thats not your problem what you need is an idler pulley if your car is overheating and not leaking then check your thermostat and radiator good luck

shipping coupon code

kids hair

How much will it cost to replace the water pump on a 2001 Ford Ranger?

So I have a pretty good size leak in either my water pump, my radiator, or somewhere in between. My friend looked at it and said that he is pretty sure its the water pump. I heard that the pump its self is about $70, but I'm still wandering about labor to install it. If someone could give me a rough estimate, that would be great!How much will it cost to replace the water pump on a 2001 Ford Ranger?Labor depends on the shop you go to. But it shouldnt exceed $250-300 with labor. If your married, i suggest buying a manual and making ur hubby do it.

How can you restart a corroded well water pump?

My family has a vacation home on the bay side of a small island off the coast of Texas. The house has a water well and uses an electric pump housed in a pump house underneath the structure, which is up on stilts. The house is infrequently used and with the seaside conditions the pump has corroded and will not start automatically. What do I need to do to clean it up so it will function? I do not believe that the motor is damaged.How can you restart a corroded well water pump?the problem with the pump not running will be the motor only.....most likely the motor rotor has rusted to the winding core of the motor ....soak it down with wd40 on the inside ...should be vent holes to spray wd40 in...try to find some way to turn rotor ....on some pumps there is a screwdriver slot on the end of the motor...if it still wont run take it to shop

How do I build a windmill driven water pump?

I have been given a project to build a windmill driven water pump. So far, a lot of the books I've researched only give me info on how a water pump works. Can anyone help me with this? Thanks in advanceHow do I build a windmill driven water pump?Basically, at least one idea, was to have the wind turn a horizontal shaft that was also a crank shaft. The crank would cause an up and down motion and was used to drive a long metal rod that went down into the well. On the end of the rod was a one-way valve. It would open on the down stroke and close on the up stroke thereby lifting out the water. I think I read there were over 50,000 of these in the western USA at one time.



I live in Arizona and they are still standing all over but few are still working. They went out of vogue when George Westinghouse started selling electricity which had the advantage of being able to pump when the wind stalled.



Google %26quot;western windmills pumps%26quot; or something similar and you can get tons of sites and images.



Annie Proulx wrote a wonderful novel, %26quot;The Old Ace in the Hole%26quot;, in which she has several scenes involving these old wonderful machines. The design was selected after testing several thousand designs and the inventor had a wind tunnel. All in the 19th century.



Amazon has some great books on windmills as I am sure Barnes/Noble does also. I have bought some of these and already have my grandson %26quot;hooked%26quot; on wind power.



India is putting in a couple hundred windmills for pumping water every year. They have over a thousand working right now.



Good Luck



PS here's a page of images



http://images.google.com/images?sourceid



Here's another great site about the inventor and some history



http://www.ironmanwindmill.com/windmill%

How to replace the water pump and thermostat on 1987 corolla?

I'd really rather not take it to a shop and pay the extra $300 or whatever for labor. Is it easy enough to do yourself? How do you do it? My Corolla is a 1987 FWD Sedan. I think it's the single overhead cam not the dual but it shouldn't make that big of a difference in terms of difficulty. Just a note, I have worked on cars before - and more then once on this car, just haven't done a water pump before. Anyone know?How to replace the water pump and thermostat on 1987 corolla?You really ought to ante up for a Chilton's or Haynes repair manual. Its only $20. Even if it doesn't have all the answers, its usually enough to get you on the right track, or tell you if its a repair you want to tackle yourself.How to replace the water pump and thermostat on 1987 corolla?remove the radiator, the fan, the fan clutch,. than you should be at the thermostat housing or water pump. remove that housing. the thermostat should be in there. make sure when you put it back together that you use a gasket and or some kind of gasket sealer or it will leak.

What is a water pump in a car? How much is it to replace?

And if it needs to be replaced, does that spell trouble for a car? I see a car I might like to buy, but the ad says that the water pump needs to be replaced. Someone please enlighten me. Thanks.What is a water pump in a car? How much is it to replace?Most water pumps are fairly cheap either new or rebuilt. Get it replaced it keeps the engine cooled off and prevents overheating.



Personally I would avoid that car unless the owner replaces the pump first. The cost is only $100 - $200 for most cars. By him replacing it you will be able to see how the car runs after, any rattling or knocking means it is toast already and not worth any more than scrap iron.What is a water pump in a car? How much is it to replace?depends on the car some are cheap and simple some are high and a big thing --as cheap as 100.00 at a shop or as much as 1000.00 depends on carWhat is a water pump in a car? How much is it to replace?Seller knows having a bad pump hurts the car's value.



How big a piece of crap is this car that they won't change the pump before trying to sell?What is a water pump in a car? How much is it to replace?Well you could ENLIGHTEN us of what car/truck that you are talking about.What is a water pump in a car? How much is it to replace?The water pump circulates the water form the radiator to the engine to help keep it from overheating. prices for water pumps range anywhere from @ $30 - $100+ and that is just the cost of the pump itself and not including the labor to install it.What is a water pump in a car? How much is it to replace?if you don't know what a water pump is you should just walk away from this car due to the fact that you will not know what else to look for and it may be a very very costly mistake for you to buy this car, now to answer you question on what is a water pump. a water pump circulates the water and coolant though the motor in to the radiator to keep your car from over heating. thing (bad things)can happen when a water pump fails like cracked and warped heads blown gaskets etcWhat is a water pump in a car? How much is it to replace?Don't buy it. I'm going through the same thing that I will fix myself and if it weren't mine I wouldn't do it for cheap either. So many things can be in the way. Also maybe it could be a headgasket which is even worse.What is a water pump in a car? How much is it to replace?Dony buy it, its probably god a blown headgasket. Depending on what year and model it is, waterpumps can be from 300 to over 800 dollars, theyre usually not easy to get to, unless youre a dodge or gm truck owner.What is a water pump in a car? How much is it to replace?I'd suggest don't buy it. The water pump cools the engine. My guess is that the person selling the car overheated the engine and knows what problems that will cause and wants to unload it on someone.



Buyer BEWARE when buying used cars.What is a water pump in a car? How much is it to replace?the water pump is what keeps the engine cool in the car if it has a bad one on it there is a small chance that it might have been drove a little hot,and this can hurt the engine in one,it can actually ruin a good engine,id be care full if i was buying this one ,it might be one to stay away from the water pump circulates the coolant all through the engine,if ts gone out it will cost a little money to replace it,just be care full you can get burned on this car real bad ,good luck with it,i hope this help,s.What is a water pump in a car? How much is it to replace?when they said it need water pump that spell big trouble!!!! when water pump went out it caused the car over heated when the car over heated it could be million thing like blow head gasket special in the older car, if you get it cheap enough or vary love the car you can check the oil to see if water mix with it or try to start it up see if it smoking if none of those exit you probably okey to buy but save a lot money for repair later on.What is a water pump in a car? How much is it to replace?I have been in the automotive cooling business for over 25 years and Michael is exactly right. Depends on the make model and year . Usually normal wear and tear on a car will cause the pump to fail it is a fast moving part but at the same rate have some one point out the cooling systems recovery bottle and look inside of it and take a whiff. If it looks bad and smells bad that could be your sign to move on to the next car. Look for rust colored stuff in the coolant bottle BUT if it is a GM product after 95 i believe they have orange coolant so don't let that through you off either.What is a water pump in a car? How much is it to replace?IT spells trouble for the car if you don't replace the waterpump. Waterpump pumps water through your engin block to keep it cool. No Water, the engine block freezes, nothing moves, engine block may crack, time for a new motor or another car.What is a water pump in a car? How much is it to replace?a water pump circulates the coolant thru the radiator to keep the engine cool. Some are outside of the engine and fairly easy to replace. others are stuck in at rediculous places and require special tools and dynamite to remove. It better be an awful nice car but at least the seller was honest about it so maybe he would be honest about th rest of the car. Its not a BIG expense but maybe you sould get an estimate so you know and can add that to what you will have to pay for the car. and get it fixed right away so you don't have to replace the engine too.

myspace images

hair straightening

How can I test how high a water pump can pump to, using only pressure simulation?

A pump is said to be capable of pumping water up to 100 meters, but I don't want to confirm that by actually putting up a very long pipe to that height. I know that pressure is related to height, so putting pressure at the output end of the pump would simulate different heights. Any suggestions how I can rig a contraption to do this? Thanks.How can I test how high a water pump can pump to, using only pressure simulation?*you can go by the 1st answer as pressure gauge near the pump discharge would give a maximum pressure inclusive of losses.

As the losses are more[due to piping congetion or rasistance from the equipment to which it is pumping.] then the discharge head will be decreased.



*Simply, in case of a centrifugal pump,close the discharge valve fully for a moment and check the discharge pressure.

This is the maximum pressure ,your pump will pump.

*Dont do this if the pump is positive displacement pump/regenerative turbine pump.



Edit: Discharge head means pumping height in your case.How can I test how high a water pump can pump to, using only pressure simulation?Install a pressure gauge at the pumps diischarge line and note that p=wh. H =p/w, H =p{(144)/62.4}/3.28 meters

Pressure expected therefore in psi, is p={62.4/144}3.28

p=14.9 psi

A pressure gauge of 0 to 50 psig range would be sufficient to indicate the expected pressure.

Does a water pump has to leakin to be bad?How can I tell if my water pump is workin?

I took out the thermostat, filled coolant level to upmost, %26amp; my car still overheats, %26amp; it doesnt leak ne where.How can I tell if the water pump is workin?Does a water pump has to leakin to be bad?How can I tell if my water pump is workin?Overheating normally would require a failed water pump. Some liquid leaking out of the weep hole normally just indicates that the pump is going to fail. Does the water pump make a clicking sound? An abnormal pump sound also is an indicator of a pump that is starting to fail.



Verify that the coolant is full. If full, check the fan. If the fan is not turning on between 185 to 225, the temperature sensor may be bad.



Also verify that the thermostat is installed in the correct direction. If installed backwards, the engine will overheat quickly. (This is an easy mistake.)



Good luck!Does a water pump has to leakin to be bad?How can I tell if my water pump is workin?check your fan thermostatDoes a water pump has to leakin to be bad?How can I tell if my water pump is workin?check rad,hoses,fan censersDoes a water pump has to leakin to be bad?How can I tell if my water pump is workin?by the sound of it, no the water pump is not working. i had the same problem with my car. it started over heating, so i replaced the radiator cap, still over heated. replaced the thermostat, and still over heated. finally i took off the water pump, to find that the fins that are inside the punp, ( that move the water around) had all corroded away. i replaced the water pump with a new one, and its been running great ever since.Does a water pump has to leakin to be bad?How can I tell if my water pump is workin?if you can look down inside the radiator watch the water see how it moves.... check you hoses if any of them are soft or fat looking.... and it dont have to leak to be bad but in most cases it leaks..... most of the time when a car over heats its a flow thingDoes a water pump has to leakin to be bad?How can I tell if my water pump is workin?water pumps are generally built with a weephole ( a spot where if coolant enters the internals in the pump it will leak out externally)



it could be a blockage in the system somwhere, radiator, engine block, or heater core

How do you change a water pump in a 1998 Cadillac Deville?

My car is overheating sometimes and I can hear clicking when it runs, I know it might be the thermostat or radiator, but I think its the water pump. I have some experience working on cars, so I would like to do the work myself. I need to know where it is located, preferably step by step instructions. I know that the water pump is not leaking. What could it be and should i do?How do you change a water pump in a 1998 Cadillac Deville?Casey if your not sure its time to see the dealer or one of your local auto repair shops.Replacing parts that might not be the problem is going to cost more.Mechanics will test your cooling system and find what is the cause of your overheating and the noise your hearing.If you decide to replace your water pump you can get free removal and installation info on www.autozone.com Best of luck.

How do I take the water pump off 2004 impala after Ive removed all the bolts and took the pulley off?

Im trying to take my water pump off but im having problems. Ive took all the bolts off the pulley and the water pump it self. How can I get it off now??How do I take the water pump off 2004 impala after Ive removed all the bolts and took the pulley off?If you've taken all the bolts out and removed the pulley and it won't come off, chances are its stuck on by the gasket. It's no great problem just give it a few taps with a wood / rubber mallet to remove it. If you don't have a mallet to hand you can use a hammer and a piece of wood. Don't strike it directly with a hammer though, it would shatter. Put the wood against it and hit the wood with the hammer.



Once it is off make sure all of the gasket has been removed and the surface is smooth before fitting a new one.

How to pump water from a water source to a water tank?

We are doing a project, and it's aimed for a community in Mali where they have a 10 month dry season. They have a swamp where they can extract water from. So we are looking to design a water pump that would feed the water into the tank. Does anyone know where could get more information on these types of water pumps, or has information on them?



ThanksHow to pump water from a water source to a water tank?Its been 20+ years since I last designed a water system (that was similar in many respects) so I don't remember the vendors. But you are either going to want a submersible pump or a verticle centrifugal pump to pull the water out of the swamp. Just google these and also google potable water pump.



You are going to have other issues such as head, flow and power requirements.



Other issues to worry about are your intake system and any screens and strainers to keep stuff out of area around the pump.



Good luck.



......................................?br>


As an add on, you might also want, depending on your system, to look at a portable fire water pump. It will get you thinking.How to pump water from a water source to a water tank?Present your question to your local water works dept. They may be delighted to give you some insight!

how do you rent an apartment

help finding niche

How to remove a water pump on a 2000 VW Jetta?

I can seam to pull out the water pump and its hard to get to. I need to replace the water pump. Anyone have suggestions? TyHow to remove a water pump on a 2000 VW Jetta?I do all my own maintenance but the first thing I always do is buy a Chilton's manual at the local parts store and look up what I want to do.Sometimes you have to get special tools and sometimes you find that there is a shortcut or a safety precaution.Good luck and hope this helps.

How to replace the water pump on a 1988 Cougar?

Im replacing the water pump on my cougar but i ran into a snag. I got the pump unbolted but to take it off, i need to unbolt a bracket that goes behind the power steering pump pulley. I cant figure out how to get that pulley off to take off the bracket. Any help with this would be greatly appreciated. Thank you.How to replace the water pump on a 1988 Cougar?go to autozone.com and look it up. You can price the parts while you're there. I think it has an electric fan and you might have to take out the entire assembly to get to the crank pulley. You'll need to remove that, the belt, the pulley, then the water pump. Replace pump and gasket; oh, and all the water that spilled out because I forgot to tell you to drain it... nevermind, I just read the rest of your question. Try this:



If equipped remove the A/C drive belt and the idler pulley bracket. Remove the alternator drive belt.



Remove the power steering drive belt and the power steering pump. Do NOT disconnect the power steering pump lines.



The rest of the instructions can be found here:

http://www.autozone.com/servlet/UiBroker



Hope that helps, if not, go get you a chilton's or hayne's manual - they come in handy for lots of things.How to replace the water pump on a 1988 Cougar?remove radiator,remove fan blade,you may have to move the a/c condenser and or compressor. and move the alternator out of the way. scrape gasket off engine block. glue new gasket to water pump and install in reverse. be sure not to over tighten the bolts.How to replace the water pump on a 1988 Cougar?it would have helped if you had given an engine size of the car the procedure is different for a v-8,and a v-6 engine,i cant answer this because i don't know an engine size,,good luck,i suggest you get a good repair manual its more informative ,and gives real good details also.

How does the radiator fan work if I replace my water pump with an electric water pump?

I have a 93 Mustang GT Convertible. The water pump went out and needs replaced. I want to replace it with an electric water pump. The problem is that the radiator fan is driven by the water pump pulley and the new electric water pump has no such pulley for a fan.How does the radiator fan work if I replace my water pump with an electric water pump?If you go to the electric pump you'll also have to go with an electric fan. However, in every car I've done this to in the past, you'll also need a high amp alternator to handle the extra load this will put on the electrical system.



BTW. Several people have asked why would you do this. You do this to free up a few horsepower by not having the extra load of the pump and fan on the engine. A higher amp alternator doesn't use any more horses to turn. The other alternative that does not work on the street though would be to do what some drag car owners do. They remove water pump, alternator, fan, and power steering. Very few horses can make a big difference in a close quarter mile pull.How does the radiator fan work if I replace my water pump with an electric water pump?%26gt;%26gt;%26gt; electric water pump?



I didn't know they made electric water pump. Are you sure?



Remember that all electrical devices have to be driven by the alternator. Putting something that draws that much current will wear out the alternator faster.

===

You can always replace your fan with electric fan. That I KNOW they make.





Good Luck...How does the radiator fan work if I replace my water pump with an electric water pump?You'll have to install an elec cooling fan on rad also. Then you would install a temperature switch to turn it on when needed.How does the radiator fan work if I replace my water pump with an electric water pump?first off why replace a vital engine part with an aftermarket gamble anyway and second it wontHow does the radiator fan work if I replace my water pump with an electric water pump?i never heard of electric water pump, all i ever saw was a pump that ran by a belt.

Can a pool pump be used to pump water from a tank to a dwelling?

Have a shack next to a water pump, and the old pump there seems to be knackered. Have an old pool pump which I thought about using in place of it, but suspect it may not be suitable, as it would be constantly pumping water, and not sure what might happen with the taps turned off! Trying to find look around on the net for some tips (on even how to troubleshoot the existing pump), but there doesnt seem to be much about. Any Ideas?Can a pool pump be used to pump water from a tank to a dwelling?Most Pool pumps are not designed to pump up, they are what is called a circulatory pump. You can buy a cheap pump for 30.00 on up at Harbour Freight tools, or you can have the old pump rebuilt.Can a pool pump be used to pump water from a tank to a dwelling?The key is the switching mechanism. You need some sort of electronic flow switch or a manual sump pump switch to detect water levels.Can a pool pump be used to pump water from a tank to a dwelling?Water pumps for wells or tanks have engines powerful enough to move the water where it needs to go (in my case, uphill). Pool pumps (depending on HP) may not have that kind of power, they are just built to recirculate water.



Even if you don't have to move the water long distances, a pool pump would be constantly pumping, which would burn out the pump, or might even blow your pipes. The pump has to have a pressure switch or the tank has to have a float switch to make it shut off when the system is full.



You could try to get it to fill temporarily with a pool pump, but it would be drained the moment you opened the taps or flushed.



We got our well pump from Sears a few years ago. Sears should have some info on their web site. Also you should do a bit of sleuthing for plumber sites about wells and water tanks, and well pumps. This is a common topic for rural dwellers. We found some sites when we changed our pump (about 3 years ago) that had some good info.



Good luck and let me know if you have any other questions.Can a pool pump be used to pump water from a tank to a dwelling?The pump will do what you would like except for the fact that you do not want the pump running when the faucet is closed, water must flow some where or the pump will burn up trying to pump the water that is going no where. It must be shut off when not in use. Most well pumps pump water into a holding tank which has a bladder inside that fills up and shuts the pump off when the bladder reaches a certain pressure. The pressure in the bladder is used to supply water pressure when the pump is not running, when a faucet is turned on the pressure in the bladder reduces to a point then the pump will turn on again to re-fill the bladder in the holding tank. You could install a regular tank like a 50 gallon drum on the roof of the shack, have a switch to turn the pump on when you need to fill the drum. The tank being located above where the faucet is located will supply the pressure needed to get water out of the faucet.Can a pool pump be used to pump water from a tank to a dwelling?best to contact the plumber or the brand of ur pump as it may void warrantyCan a pool pump be used to pump water from a tank to a dwelling?First of all you need to be sure that the pump has failed and not just the motor. Pumps fail when the shaft seal leaks and you get more water dripping out the shaft seal than the pump is pushing. If it;s the motor, then you might be able to buy just a replacement motor and attach the old pump to the new motor.



As for a smimming pool pump, I think it would work, depending upon the flowrate and pressure you are looking for. My pool pump puts up about 20 lbs discharge pressure, but only a couple of gallons per minute. If you need large volume flow and higher pressure, you will want to look for another pump.Can a pool pump be used to pump water from a tank to a dwelling?YOUR PRESSURE TANK ON A WEEL SYSTEM IS THE SHOCK ABSORBER... IF YOU SHUT THE VALVE, B-4 THE PUMP HAS STOPPED ( WITH OUT A PRESSURE TANK ) YOUR PIPES EXPLODE! WATER DOES NOT COMPRESS!Can a pool pump be used to pump water from a tank to a dwelling?The electrical control system for a well pump includes a high pressure shutoff switch so that the pump will shutdown when there is enough pressure in the system.



This serves two functions, first it saves energy, second, it prevents the pump from overheating.



A pump overheats because the motor is suppling energy to the fluid being pumped. That energy exhibits itself as both pressure, and increased temperature.



Normally if there is flow through the pump the increase in temperature is barely measurable because there is a high flow of water and the energy is dispersed over the hundreds of gallons of water that is being pumped by the pump, however, if no water is flowing through the pump, less than a gallon of water is absorbing all of the energy from the pump, and that water can rapidly heat up and even start boiling.



There are three very important design factors that an engineer would look at when designing a pump for a given service:



1) What Discharge Pressure do I need?

2) What Flow do I need?

3) What will the suction pressure be at the pump?



All three of these factor into the choice of pump for the application.



Usually a well pump would be designed to turn on when the pressure drops to about 30 psig, and turn off when the pressure is above 50 psig. 15 to 40 gpm would be a typical design flows for a well pump, and the suction conditions are going to depend on the location of the pump in relation to the location of the water.



Some pumps are designed for %26quot;Suction Lift,%26quot; Others have to be lowered into the water and run submerged because they are not designed to %26quot;lift%26quot; the water.



In either case, the feet of lift has to be figured into the design of the pump and subtracted from the discharge pressure.



Because of these 3 factors, a pump designed for one service seldom will work in another service.



If the pump does not have enough suction lift, it will gas up and stop pumping (and overheat)



If a pump does not have enough discharge pressure, it won't be able to make it up to the second floor, or even the first floor, AND the pump discharge pressure will never hit the pump shutoff pressure, it will run all of the time and overheat.



And if a pump does not have enough flow, you will not be able to do things the way your are used to doing them, for example, your watering system may just dribble, or you might only get a small flow at the shower.



If you have any operating data or design data on the pool pump you could determine if it has a discharge pressure and flow that is in the ballpark as a temporary replacement for your well pump. It likely does not, but it doesn't hurt to check.



If the pool pump somehow happens to be a match on pressure and flow, it still may not be a match for the suction lift. Unless you have spec sheets for the pool pump you will not know one way or another. You could try to install the pool pump with the intent of removing it if it did not work.



As for the pressure shutdown, that is normally should be tied into the electrical supply to the pump. As long as you wire the pump up using the same electrical systems you should be ok. (Make sure the wiring is large enough for the new pump!)



Again though, I will stress that the chances of the pumps matching well enough to interchange them is very low!